1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

[Workblog] Al-CONH Desk

Discussion in 'Die-hard Overclocking & Case Modifications' started by JejeLaPelle, Oct 10, 2018.

  1. JejeLaPelle

    JejeLaPelle Member

    Messages:
    46
    Likes Received:
    8
    GPU:
    970 HoF
    Hello!

    Let me introduce my new mod, a deskmod made of wood (pine), with two watercooling loops, nickel plated copper tubes mixed with acrylic tubes, and some aluminium touch.
    Al-CONH refers to atoms of aluminium and wood, which is mainly made of carbon, oxygen, nitrogen and hydrogen (wikipedia says it...).

    This project is supported by EKWB and Gamers Industry.

    [​IMG]
    [​IMG]
    I would like to thanks EKWB for trusting me again, especially Atila for his time!
    I also thanks Gamers Industry for their help (it's a french retailler for MDPC-X, but also Singularity Computers and soon Bitspower).

    Here is the concept :

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    The structure is really classic, two chambers, the main one for the MB/GPU/PSU, some radiators and pumps, and the other one to hide the tubbing, put some more radiators, a more technical chamber.

    Now, the hardware :
    • AMD R7 1700X
    • Asus Crosshair Extreme VI
    • Asus 1080ti Strix OC
    • 4*8Go Corsair Vengeance RGB RAM 2666MHz
    • Corsair RM650
    • Corsair MP500 120Go
    • Crucial MX200 500Go
    • Corsair lighning node pro
    • Cooler Master Riser
    And the cooling :
    • WB CPU : Monoblock C6H
    • WB GPU : Full cover 1080ti Strix acrylic/nickel
    • Rad : EK- XE480 2* EK-PE360 and EK- XE240
    • Fittings : EK-HDC 12mm (nickel/black)
    • Pump : two D5
    • Watertank : EK-X3 40cm
    • Fans : EK-Vardar RGB, Corsair HD120
    • Flowmeters : home made
    Sleeveing :
    • MDPC-X sleeve and connectors
    I'm close to the end of the big wood work (the desk is nearly done), i'll soon make a big post one the wood job.
    It was new for me, but really interesting, i'm now planning to do a lot of custom furniture (my wife will be happy).
    See you soon.
     
  2. JejeLaPelle

    JejeLaPelle Member

    Messages:
    46
    Likes Received:
    8
    GPU:
    970 HoF
    Hello,

    I've been a bit long to do this post, lot of work, but here I am !

    So here is the big post on the wood work i've done so far (main part is done, i've got few things to finish).

    First of all, DISCLAIMER : this is the first time i'm using wood, so i'll tell you my feelings, the things i've done that were crap, the things i do that were fine ect... I'm not a pro!
    And of course, always think safety!! Be carefull, further more while using electrical tools.


    To realise this work i used :

    • A plunging router (mine was a Bosch)
    • A router bit set
    • A Jigsaw
    • A drill machine
    • A set of guides (iron bars)
    • A set of clamps (i really like the ratchet bar clamps)
    • A Pocket Hole Woodjoining Jig Kit (Wolfcraft for mine)

    [​IMG]


    I think that those tools are a very good start to make furnitures (the last one is not really mandatory, but helps a lot).

    I could have add a circular saw, but i do not own one, so i did my best without it.

    Of course, i made a sketch to get the pattern of the differents parts.

    Now, to realise those parts, the first thing is to put your wood piece to the good size.

    The best way to do that, is to have a circular saw, this tool does really nice cuts... But as said before, i don't have this thing, so.....

    What i've done, is getting close to the good measure with a jigsaw (horrible cut here, i do not use guide)

    [​IMG]

    And then i place a guide and i use the router to get the final size.
    To place the guide, you have to know the distance beetween the center of rotation of the drill and the flat side of the router, then substract the half of diameter of the router bit, and you have the distance beetween your final measure and your guide.

    [​IMG]

    Don't forget to clamp your wood piece AND your guide, it should not move, i used at least 4 clamps each time, sometimes 6 to be sure everything won't move.

    [​IMG]

    If it moves, you can easily ruin your job and have to restart!

    After that, i choosed a router bit long enought, then move your router against the rotation of the bit (using your guide).

    Now you have a perfect shape cut, with precise size (i'm at less than a millimeter on each parts). And...

    TONS OF WOOD SHIPS AND DUST!

    So yes, you need to work in a adapted place.

    After that, i used exactly the same technic for each cuts.

    When doing polygonial holes, to get a nice finish you have to watch carefully where you stop/begin using the router.

    [​IMG]

    There is also bits with rollers, i used them to shape borders, to chamfer or make borders round. It's really easy to do, and the result is awesome (this is clearly my favorite moment).

    [​IMG]

    To mount each part, is used the woodjoining jig kit, wich allow you to make a hole with a angle in your wood, so you can use a screw to fix two parts together. It's easy to use, i highly recommend it!

    [​IMG]

    [​IMG]

    I'll just detail a bit the work done of the top of the desk, wich is the hardest part i had to do.

    I would like to have a hole for the glass panel (logic....) and i wanted it to be supported all around by a groove AND by reinforcement at the 4 corners, all of that in the same wood piece.

    So i first i used jigsaw to make the main hole, make the good size/good finish with router, as always.

    Then, at the reinforcement place, i used the router to remove 10mm (the glass thickness).

    After, i did the holes in the corners, the groove everywhere.

    [​IMG]

    [​IMG]

    Doing the things in the right order is really important, if i had done the holes in the corners, i would not have been able to properly remove the 10mm on the reinforcements, as there would have been no more wood to support the router.

    Always think twice, make the moves in you head, is it possible, is it painfull ? You often can find a way to make it better/easier !

    Now here is the result !

    [​IMG]

    Better picts soon

    I’m really happy, and now, I’m working on the watercooling part (wich means also a bit of wood work to make everything fit well).

    A little tease :

    [​IMG]

    Bye, thanks for passing by!
     
    Koniakki and The1 like this.
  3. Koniakki

    Koniakki Ancient Guru

    Messages:
    2,650
    Likes Received:
    251
    GPU:
    ZOTAC GTX 1080Ti FE
    Looks like it's gonna be a great desk build!
     
  4. JejeLaPelle

    JejeLaPelle Member

    Messages:
    46
    Likes Received:
    8
    GPU:
    970 HoF
    Hello,

    Today i will introduce the watercooling part.

    Obviously, the first thing is to thanks again my sponsor EKWB (and Atila) for all this mighty stuff!

    [​IMG]

    As you might see, there is a Velocity block inside, i rushed on it, and really, the block is really cool (even without water)

    [​IMG]

    I placed pumps :

    [​IMG]

    [​IMG]

    Quite fun to see how it fit with the sketch :

    [​IMG]

    Then the huuuuuge res... the tubbing is a bit different from the 3d model, but like this, res will play better there role of bubble trap :

    [​IMG]

    [​IMG]

    [​IMG]

    I also did a small wood plate, but here is only a tease, i got to finish it... :

    [​IMG]

    I also milled flow meters, since EK do not provide such things yet :

    [​IMG]

    [​IMG]

    Wheel is 3D printed with EK logo on it. Those flow meter will be used as pass throught on the right side, above the 360mm rads.

    And few words for the RGB build wich lighted up for the last time :

    [​IMG]

    [​IMG]

    All the block were super clean after one year of use

    [​IMG]

    [​IMG]

    I'll be back ASAP for a post on sleeeeving!

    Thanks for reading.
     
    vbetts likes this.

  5. JejeLaPelle

    JejeLaPelle Member

    Messages:
    46
    Likes Received:
    8
    GPU:
    970 HoF
    hello!
    I'll show you the job done on the sleeving part, and once again, i'll begin with a big thanks to Gamers Industry, for those who do not know them, it's a french store that makes customs PC and retail brands hard to find in France like Bitspower, Singularity Computers and Team Group.
    All the sleeve use here is MDPC-X Small.
    I won't explain how to sleeve, there is a ton of tutorials, I follow one myself, so it won't be revelant to write one.
    What i can say, is that i really enjoyed doing this, this is not that long and do not requiere too many tools.
    I used a lamptron modding tool, a molex hand crimp tool, and a small tool for the heatshrink (http://cableorganizer.fr/torche-micro-therm-mj-600.html).
    [​IMG]
    [​IMG]
    I choosed natural white, white carbon, blue carbon, carbon and blue magic
    For the wire i've used a 1.34mm² of section cable ( 16 awg), i think it's absolutly perfect with this sleeve.
    I first tried with fans :
    [​IMG]
    And with the block :
    [​IMG]
    For each RGB connector, i removed with cutter the SIL part :
    [​IMG]
    [​IMG]
    marked the 12v, unsolder, put the sleeve + heatshrink, resolder.
    Now the result for the main cables :
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    Next time, i'll show you the best part i've done so far, a distribution plate.
    Have a nice day!
     

Share This Page