The GTX 1080-Ti Thread

Discussion in 'Videocards - NVIDIA GeForce' started by XenthorX, Sep 18, 2016.

  1. Mufflore

    Mufflore Ancient Guru

    Messages:
    10,336
    Likes Received:
    59
    GPU:
    1080ti @2GHz air
    Good wise up.
    Good job I didnt have any LM tim or I might have tried it.
    Gelid Extreme ftmf safe win :)
     
  2. fantaskarsef

    fantaskarsef Ancient Guru

    Messages:
    6,964
    Likes Received:
    47
    GPU:
    1080Ti @h2o
    A shunt mod is nice, but aren't most cards crippled by the temp target anyway? Unless LN2'ing of course.
     
  3. Mufflore

    Mufflore Ancient Guru

    Messages:
    10,336
    Likes Received:
    59
    GPU:
    1080ti @2GHz air
    Even the FE cooler can keep temps below 70C but its quite loud.
    Aftermarket cards and alternative coolers even better.

    My Accelero Xtreme III cooler gives a max overclock load temp while stress testing of 51C, 24C ambient.
    Gaming temps are lower.
    And its silent.
     
    Last edited: Jul 12, 2017
  4. Mars73

    Mars73 Member

    Messages:
    26
    Likes Received:
    2
    GPU:
    Gigabyte AORUS GTX1080Ti
    Or just don't do it, the card is imo too expensive to mess around with.
    Getting my Ti next week, if deliveries goes as planned.
    Looking forward to it.
     

  5. Agent-A01

    Agent-A01 Ancient Guru

    Messages:
    9,810
    Likes Received:
    62
    GPU:
    1080Ti H20
    I wouldn't bother.

    XOC bios is just too easy and end results are the same, if not a little better.
    Zero power throttling.
     
  6. chispy

    chispy Ancient Guru

    Messages:
    7,845
    Likes Received:
    46
    GPU:
    GTX1080Ti @ 2126/6156 H2O
    I think i'm going to flash the eVGA FTW Bios and call it a day as i already know how Pascal cards behave ( Used to have GTX 1070 ) , since i'm on H2O full cover EK water block temperatures for an hour of stress testing the video card 3DMark Time Spy loop maxed out at 37c flat line all across and it never reaches 38c with room temperature of ~27c.
     
  7. fantaskarsef

    fantaskarsef Ancient Guru

    Messages:
    6,964
    Likes Received:
    47
    GPU:
    1080Ti @h2o
    Yes I think flashing the right BIOS is a lot safer and brings about the same gains as a real shunt mod. Mind you, shunt mods are what brings the LN2 clockers to the tops in benchmark ranks, but I doubt that every day use needs such a procedure to achieve good effects.
     
  8. chispy

    chispy Ancient Guru

    Messages:
    7,845
    Likes Received:
    46
    GPU:
    GTX1080Ti @ 2126/6156 H2O
    Correct :thumbup: . I just flashed the Asus XOC bios to overcome the power limits and voltages limits + water cooling will overcome the temperature limits and with that out of the way now it's up to the silicon lottery Gods :giggle2: , will do some testing during the weekend to see where i stand clock wise , i need 100% stable OC for gaming ( will make a profile in AB for that ) and will test for maxed out clocks for benchmarking purposes only.
     
    Last edited: Jul 15, 2017
  9. IcemaN22

    IcemaN22 Member Guru

    Messages:
    120
    Likes Received:
    0
    GPU:
    Asus 1080Ti ROG STRIX
    Hello all. Im a new owner of a Asus 1080Ti. After I upgraded from 980Ti, I started having some problems with PUBG where the nVidia driver "nvlddmkm" stopped responding, and fail to recover. I'm using the 382.53 driver and have only factory overclock. So far this is the only game where this freeze is happening. Anyone here experienced the same ?
     
  10. A M D BugBear

    A M D BugBear Ancient Guru

    Messages:
    2,532
    Likes Received:
    1
    GPU:
    2 1080ti h20 w/XOC Bios
    Hello, whats your power target now?
     

  11. A M D BugBear

    A M D BugBear Ancient Guru

    Messages:
    2,532
    Likes Received:
    1
    GPU:
    2 1080ti h20 w/XOC Bios
    Hi, flashing to xoc works well, but one problem, the XOC Voltage Tool, I tried using that program and keeps saying: error error error.

    Says does not detect asus strix card,

    Tried flashing to that, same problem

    Question concering the XOC bios:

    Once flashed to this bios, I do understand that all power stuff that was holding the card back has been removed, but do you need the xoc voltage tool as well? Or does the bios automatically distribute whatever power is needed?
     
    Last edited: Jul 17, 2017
  12. fantaskarsef

    fantaskarsef Ancient Guru

    Messages:
    6,964
    Likes Received:
    47
    GPU:
    1080Ti @h2o
    Good question. I believe though, that AB should be fine, as you're not running any specific voltage controller (like Strix cards) that would need any in depth talking to the chip?
     
  13. Agent-A01

    Agent-A01 Ancient Guru

    Messages:
    9,810
    Likes Received:
    62
    GPU:
    1080Ti H20
    There are no TDP sliders anymore as there is zero power limiting.

    As for voltage, you can change it.

    Use MSI afterburner to edit curve to set the voltage/clock speeds that you want.

    Don't bother with XOC tool
     
  14. A M D BugBear

    A M D BugBear Ancient Guru

    Messages:
    2,532
    Likes Received:
    1
    GPU:
    2 1080ti h20 w/XOC Bios
    That's the problem, I can't get the voltage curve to show up, it will not show.

    I tried the way this site shows it:

    http://www.overclock.net/t/1625653/how-to-get-voltage-slider-in-afterburner-working-on-a-1080-ti

    But I can't get it to work.

    What do I write on the bottom of that oem2 file???

    Do I use the wildcard file?

    Cause it doesn't work.

    Also, there was a video I seen awhile back, it showed his fps,etc,etc and also his maximum tdp draw, while onscreen, do you know which program is this?

    UPDATE:

    Wait a min, Couldn't I just use slider within Precision XOC?, the xoc can go as high as 1162mv, whereas the msi ab version go as high as 1200mv.

    I like using the xoc cause of the fan control, msi ab, for some reason, fan on card doesn't turn on.

    OK, NVM ME:

    LOL, Cntrl+F, its not shown by default, had to look it up some. Question about the curve editor, how in the hell can you increase the gpu MV while at a lower gpu speed? Reason why I asked, certain benchmark with certain settings such as sparsgrid absolutely brutalized the card, and must jock down the gpu big time in order to gain more stability, another to help stability Is voltage but how in the heck can you make the editor increase voltage @ 1800mhz lets say, like from 1800mhz to 2000mhz, uses 1200mv throughout.

    UPDATE:

    LOL, All my problems has been solved, Please check my newest post on my bios mod, VERY GOOD thread.

    Very staggering results.
     
    Last edited: Jul 17, 2017
  15. IcemaN22

    IcemaN22 Member Guru

    Messages:
    120
    Likes Received:
    0
    GPU:
    Asus 1080Ti ROG STRIX
    I've never touched that setting, so it is 100%,
     

  16. chispy

    chispy Ancient Guru

    Messages:
    7,845
    Likes Received:
    46
    GPU:
    GTX1080Ti @ 2126/6156 H2O
    There you go AMDbugbear. Easiest way to learn how to use the curve overclocking on msi afterburner :thumbup:





     
  17. A M D BugBear

    A M D BugBear Ancient Guru

    Messages:
    2,532
    Likes Received:
    1
    GPU:
    2 1080ti h20 w/XOC Bios

    Thanks alot but I fixed everything in the throttling dept.

    Check out my 1080ti bios mod on this site, Everything is taken care of.
     
  18. judi

    judi Banned

    Messages:
    10
    Likes Received:
    0
    GPU:
    GTX1050/4gb
    it will get more drop after they release 1080Ti
     
  19. fantaskarsef

    fantaskarsef Ancient Guru

    Messages:
    6,964
    Likes Received:
    47
    GPU:
    1080Ti @h2o
    As each post requires more letters, here what I wanted to post:

    ?
     
  20. Witcher29

    Witcher29 Master Guru

    Messages:
    849
    Likes Received:
    1
    GPU:
    1080 Ti Gaming X SL
    U guys are ruining your GPU,s this way, anyway enjoy all your gtx 1080 ti.
     

Share This Page