RadeonMod (Tweak Utility)

Thanks, i am tested, but i cannot see any difference(

 

Hi) Please explain, why in your reg file vsync have this values? "Main3D_DEF"="3" is Dynamic sync and its now work or i am wrong? And waht mean "Main3D"=hex:33,00,00,00 default values is 0x3000,0x3100,0x3200 or 0, 1, 2?

Code:

"Main3D_DEF"="3"
"Main3D"=hex:33,00,00,00

 

This is how many frames CPU will deliver to GPU prior before rendering.
1,2,3 FPS -> 3 or 2 is best Value for this.

 

what's the best option if your cpu is slow and your gpu is fast?

 

Make 2 (also try 1)

 

Works great with 2. Thanks!

 

Maybe exist some way to increase sharpnes on transparent textures?
In Dx9 games exist a interesting feature how to make transparent textures visible. Turn on Eqaa+ Surface Optimisation. But it works only for DX9 games.Maybe exist another way?

 

hello sir. radeon settings enhanced sync enable in game screen tearing have. 144 hz 1 ms monıtor 8700k rx 580 gpu use I have never had such a problem before i saw you were the last drivers. how to fix works enhanced sync thank you.

 

Try FRT at 142/143FPS (Hz)
Also try to disable E.Sync -> set OFF, app. decides

 

Under 60 fps, the screen tearing have. vsync does not activate. how to fix ?

 

Hi, can anyone share the best performance settings? Thanks in advance.

 

Maby Try V.Sync in Game ON
E.Sync ON, then OFF
FRT at desired FPS ON or OFF
Disable chill.

Depends on Game, for BFV/1 i need to disable FRT, leaving only 74FPS in user.cfg.
You need to go try & error rute, i can't help much more.

 

not works radeonmod how to fix ? https://pasteboard.co/IGOqg1c.jpg

 

Admin Mode?
Make sure You have Full control of the Mod folder.

 

yes ı have https://pasteboard.co/IH4OrdB.jpg but no works

 

Try to download again and un-pack into different directory e.g. Dysk D: (not C: )

 

Does anyone know what the "StutterMode" setting actually does? RadeonMod says the valid values are 0, 1, and 2, but in my registry it is set to 8202 by default.

I also had a rather harrowing experience, I changed StutterMode, Main3D, Main3D_DEF, and Main3D_SET all to 0. Then when I hit restart driver, it went into software mode, and never came back. The card would not show up in device manager or anywhere else, windows said it was not connected. When I rebooted and went into the BIOS the display was corrupted into rainbow colours.

Luckily I had an APU so I was able to fiddle about in windows using the onboard graphics, I tried a lot of things including pulling it out of the case and putting it back in, but nothing could make the card work again, but as far as windows was concerned it did not exist at all. In the end I took the card out and left it on the desk overnight. In the morning when I plugged it back in and it worked again.

So now I am a bit wary of this stuttermode setting. It would be nice to have some explanation as to what it does. Normally I would just experiment and try to observe what it does but I'm not too eager to do that anymore.

 

This question should be ask in the ATI/AMD forums.
I can't say for sure, all options that i know (99% sure) is clarified in Mod.

Note:
You can always Tweak & test to see what it does (write down original value to revert back).

 

Any opinions about XtremeG driver.
And what there difference in performance and quality vs. Normal Amd drivers??

 

Don't change it, or you will experience black screen.