ClockTuner for Ryzen (CTR) - and introduction guide and download

Discussion in 'Processors and motherboards AMD' started by Hilbert Hagedoorn, Sep 29, 2020.

  1. Dale Roble

    Dale Roble New Member

    Messages:
    1
    Likes Received:
    0
    GPU:
    RX5700XT
    I stopped running the tuning after the clock speed for CCX2 dropped below stock rated speed. Here is a portion of my log. Also noticed that processor detection not relable. Sometimes says platinum and sometimes says bronze.

    ***ClockTuner for Ryzen 1.0s by 1usmus***
    AMD Ryzen 3 3100 4-Core Processor (870F10)
    Gigabyte Technology Co., Ltd. B550 AORUS ELITE AX
    BIOS ver. F10a SMU ver. 46.64.00
    DRAM speed 3200 MHz
    09/30/2020 22:51:12


    AVX light mode
    Cycle time: 45000 ms
    Reference frequency: 4050MHz
    Reference voltage: 1225 mV
    Voltage step: 6 mV


    Manual overclocking mode enabled
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4050 MHz Voltage 1225 mV
    CCX2 Quality 115 Frequency 4050 MHz Voltage 1225 mV

    Step# 1
    Diagnostic VID voltage: 1225 mV
    Stress test started! 09/30/2020 22:51:26
    Try to use a softer LLC. This warning may be ignored.
    SOC SVI2 1.094
    Thread# 9 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:51:30

    Step# 2
    Diagnostic VID voltage: 1231 mV


    Diagnostic results:
    Energy efficient: 3.29
    AMD Ryzen 3 3100 4-Core Processor - Platinum sample
    Recomended values for Overclocking:
    Reference frequency: 6424 MHz
    Reference voltage: 1262 mV
    Recomended values for Undervoolt:
    Reference frequency: 6300 MHz
    Reference voltage: 1175 mV
    AVX Light mode
    Cycle time: 240000 ms
    Reference frequency: 4100 MHz
    CCX delta: 25 MHz
    Reference voltage: 1262 mV
    Target voltage: 1262 mV


    Cinebench 20 started
    Cinebench 20 finished with result: 2298
    Voltage: 1.2 V PPT: 38.6 W Temperature: 68.7°
    Manual overclocking mode enabled

    Step# 1
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 4100 MHz Voltage 1262 mV OC+
    Stress test #1 started! 09/30/2020 22:54:51
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 78.7°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:54:56

    Step# 2
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 4075 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:54:57
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 78.5°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:01

    Step# 3
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 4050 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:02
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.3°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:07

    Step# 4
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 4025 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:08
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.8°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:13

    Step# 5
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 4000 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:14
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.7°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:18

    Step# 6
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3975 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:19
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.8°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:24

    Step# 7
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3950 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:25
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.7°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:29

    Step# 8
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3925 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:30
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 80°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:35

    Step# 9
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3900 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:36
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.9°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:40

    Step# 10
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3875 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:41
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 80.1°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:46

    Step# 11
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3850 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:47
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 79.7°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:52

    Step# 12
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3825 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:53
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 80.2°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:55:57

    Step# 13
    Sets overclocking parameters...
    CCX1 Quality 108 Frequency 4100 MHz Voltage 1262 mV OC+
    CCX2 Quality 115 Frequency 3800 MHz Voltage 1262 mV OC=
    Stress test #1 started! 09/30/2020 22:55:58
    FFT: 2048 CPU Vdroop: 0.6 % CPU Temperature: 80.1°
    Try to use a softer LLC. This warning may be ignored.
    CCX2 overclocking failure detected!
    Thread# 5 fall down, usage 0%
    Stress test stopped! 09/30/2020 22:56:03
     
  2. Mentat_Teg

    Mentat_Teg New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    EVGA 1080ti
    I am not having much luck getting this to run, i keep getting critical error, core tags not defined. ive cleared system logs and rebooted. any thoughts?
     
  3. Mentat_Teg

    Mentat_Teg New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    EVGA 1080ti
    Hi, read the guide cleared logs and rebooted, my bios is setup correctly as well. any thoughts?

    ***ClockTuner for Ryzen 1.0s by 1usmus***
    AMD Ryzen 7 3800X 8-Core Processor (870F10)
    Gigabyte Technology Co., Ltd. X570 AORUS ELITE
    BIOS ver. F20a SMU ver. 46.62.00
    DRAM speed 3600 MHz
    10/01/2020 02:11:34




    Critical error. Core tags are not defined correctly!
    You should read the guide.
     
  4. J0eri

    J0eri New Member

    Messages:
    5
    Likes Received:
    1
    GPU:
    1070 Ti
    I used beta 2 but the system keep crashing/rebooting when running start after the diagnostic. Ryzen 3600X on a Asus Rog Strix X370-F Gaming. Not once was I able to finish. Log cleared, Bios setup ok. Tried all LLC.

    Is this a no go on a X370 board?
     

  5. Henning

    Henning New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    GTX 970 Strix 4GB
    I have tried getting the diagnostics to run through and give me a result, but it seems like it just goes on forever and then suddenly it crashes and I don't get any result at all.
    Any ideas why this is?
    I set all the settings in the BIOS and made sure there was no memory overclock. Running a Ryzen 5 3600 with 2x8GB Corsair LPX 3200 CL16 sticks in a MSI B450 Tomahawk Max with Corsair RM750x PSU.
    CTR beta2 diagnostics.png
    [​IMG]
     
  6. Henning

    Henning New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    GTX 970 Strix 4GB
    Sorry for double posting. I just wanted to add the logs from my latest diagnostics try:
    ***ClockTuner for Ryzen 1.0s by 1usmus***
    AMD Ryzen 5 3600 6-Core Processor (870F10)
    Micro-Star International Co., Ltd B450 TOMAHAWK MAX (MS-7C02)
    BIOS ver. 3.70 SMU ver. 46.62.00
    DRAM speed 3200 MHz
    10/01/2020 08:44:31


    AVX light mode
    Cycle time: 45000 ms
    Reference frequency: 4050MHz
    Reference voltage: 1268 mV
    Voltage step: 6 mV


    Manual overclocking mode enabled
    Sets overclocking parameters...
    CCX1 Quality 116 Frequency 4050 MHz Voltage 1268 mV
    CCX2 Quality 127 Frequency 4050 MHz Voltage 1268 mV

    Step# 1
    Diagnostic VID voltage: 1268 mV
    Stress test started! 10/01/2020 08:47:17
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 08:48:07

    Step# 2
    Diagnostic VID voltage: 1262 mV
    Stress test started! 10/01/2020 08:48:08
    Stress test stopped! 10/01/2020 08:48:58

    Step# 3
    Diagnostic VID voltage: 1256 mV
    Stress test started! 10/01/2020 08:48:58
    Stress test stopped! 10/01/2020 08:49:48

    Step# 4
    Diagnostic VID voltage: 1250 mV
    Stress test started! 10/01/2020 08:49:49
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 08:50:39

    Step# 5
    Diagnostic VID voltage: 1244 mV
    Stress test started! 10/01/2020 08:50:39
    Stress test stopped! 10/01/2020 08:51:29

    Step# 6
    Diagnostic VID voltage: 1238 mV
    Stress test started! 10/01/2020 08:51:30
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 08:52:20

    Step# 7
    Diagnostic VID voltage: 1232 mV
    Stress test started! 10/01/2020 08:52:20
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 08:53:10

    Step# 8
    Diagnostic VID voltage: 1226 mV
    Stress test started! 10/01/2020 08:53:10
    Stress test stopped! 10/01/2020 08:54:00

    Step# 9
    Diagnostic VID voltage: 1220 mV
    Stress test started! 10/01/2020 08:54:01
    Stress test stopped! 10/01/2020 08:54:51

    Step# 10
    Diagnostic VID voltage: 1214 mV
    Stress test started! 10/01/2020 08:54:51
    Stress test stopped! 10/01/2020 08:55:41

    Step# 11
    Diagnostic VID voltage: 1208 mV
    Stress test started! 10/01/2020 08:55:42
    Stress test stopped! 10/01/2020 08:56:32

    Step# 12
    Diagnostic VID voltage: 1202 mV
    Stress test started! 10/01/2020 08:56:32
    Stress test stopped! 10/01/2020 08:57:22

    Step# 13
    Diagnostic VID voltage: 1196 mV
    Stress test started! 10/01/2020 08:57:23
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 08:58:13

    Step# 14
    Diagnostic VID voltage: 1190 mV
    Stress test started! 10/01/2020 08:58:13
    Stress test stopped! 10/01/2020 08:59:03

    Step# 15
    Diagnostic VID voltage: 1184 mV
    Stress test started! 10/01/2020 08:59:04
    Stress test stopped! 10/01/2020 08:59:54

    Step# 16
    Diagnostic VID voltage: 1178 mV
    Stress test started! 10/01/2020 08:59:54
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:00:44

    Step# 17
    Diagnostic VID voltage: 1172 mV
    Stress test started! 10/01/2020 09:00:45
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:01:35

    Step# 18
    Diagnostic VID voltage: 1166 mV
    Stress test started! 10/01/2020 09:01:35
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:02:25

    Step# 19
    Diagnostic VID voltage: 1160 mV
    Stress test started! 10/01/2020 09:02:26
    Stress test stopped! 10/01/2020 09:03:16

    Step# 20
    Diagnostic VID voltage: 1154 mV
    Stress test started! 10/01/2020 09:03:16
    Stress test stopped! 10/01/2020 09:04:06

    Step# 21
    Diagnostic VID voltage: 1148 mV
    Stress test started! 10/01/2020 09:04:07
    Stress test stopped! 10/01/2020 09:04:57

    Step# 22
    Diagnostic VID voltage: 1142 mV
    Stress test started! 10/01/2020 09:04:57
    Stress test stopped! 10/01/2020 09:05:47

    Step# 23
    Diagnostic VID voltage: 1136 mV
    Stress test started! 10/01/2020 09:05:48
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:06:38

    Step# 24
    Diagnostic VID voltage: 1130 mV
    Stress test started! 10/01/2020 09:06:38
    Stress test stopped! 10/01/2020 09:07:29

    Step# 25
    Diagnostic VID voltage: 1124 mV
    Stress test started! 10/01/2020 09:07:29
    Stress test stopped! 10/01/2020 09:08:19

    Step# 26
    Diagnostic VID voltage: 1118 mV
    Stress test started! 10/01/2020 09:08:20
    Stress test stopped! 10/01/2020 09:09:10

    Step# 27
    Diagnostic VID voltage: 1112 mV
    Stress test started! 10/01/2020 09:09:10
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:10:00

    Step# 28
    Diagnostic VID voltage: 1106 mV
    Stress test started! 10/01/2020 09:10:01
    Stress test stopped! 10/01/2020 09:10:51

    Step# 29
    Diagnostic VID voltage: 1100 mV
    Stress test started! 10/01/2020 09:10:51
    Stress test stopped! 10/01/2020 09:11:41

    Step# 30
    Diagnostic VID voltage: 1094 mV
    Stress test started! 10/01/2020 09:11:42
    Stress test stopped! 10/01/2020 09:12:32

    Step# 31
    Diagnostic VID voltage: 1088 mV
    Stress test started! 10/01/2020 09:12:32
    Stress test stopped! 10/01/2020 09:13:22

    Step# 32
    Diagnostic VID voltage: 1082 mV
    Stress test started! 10/01/2020 09:13:23
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:14:12

    Step# 33
    Diagnostic VID voltage: 1076 mV
    Stress test started! 10/01/2020 09:14:13
    Stress test stopped! 10/01/2020 09:15:03

    Step# 34
    Diagnostic VID voltage: 1070 mV
    Stress test started! 10/01/2020 09:15:04
    Stress test stopped! 10/01/2020 09:15:54

    Step# 35
    Diagnostic VID voltage: 1064 mV
    Stress test started! 10/01/2020 09:15:54
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:16:44

    Step# 36
    Diagnostic VID voltage: 1058 mV
    Stress test started! 10/01/2020 09:16:45
    Stress test stopped! 10/01/2020 09:17:35

    Step# 37
    Diagnostic VID voltage: 1052 mV
    Stress test started! 10/01/2020 09:17:35
    Stress test stopped! 10/01/2020 09:18:25

    Step# 38
    Diagnostic VID voltage: 1046 mV
    Stress test started! 10/01/2020 09:18:26
    Stress test stopped! 10/01/2020 09:19:16

    Step# 39
    Diagnostic VID voltage: 1040 mV
    Stress test started! 10/01/2020 09:19:16
    Stress test stopped! 10/01/2020 09:20:06

    Step# 40
    Diagnostic VID voltage: 1034 mV
    Stress test started! 10/01/2020 09:20:07
    Try to use a softer LLC. This warning may be ignored.
    Stress test stopped! 10/01/2020 09:20:57

    Step# 41
    Diagnostic VID voltage: 1028 mV
    Stress test started! 10/01/2020 09:20:57

    edit: And it just rebooted again at step #45.
     
    Last edited: Oct 1, 2020
  7. Athlonite

    Athlonite Maha Guru

    Messages:
    1,335
    Likes Received:
    43
    GPU:
    Pulse RX5700 8GB
    Here's mine after a BSOD on first run with msg Stop Code: Memory Management

    successful tune

    [​IMG]

    CB20 results

    [​IMG]
     
  8. daghtus

    daghtus Member

    Messages:
    25
    Likes Received:
    6
    GPU:
    RTX 2080S, 8 GB
    In my case, CTR works (almost) flawlessly. OK, it sometimes doesn't apply settings upon OS startup and Prime95 sometimes doesn't kick in but I made the diagnostics to work (my R5 3600 is apparently a golden sample) and I was able to achieve stable 4425 MHz at CCX1 and 4400 MHz at CCX2 under 1.275 V. I set CPU LLC as well as SoC LLC to Level 3 at my Asus Strix X570 E-Gaming mobo. The guide never said anything about SoC LLC so I was just wondering if it's okay.
    What is worrying me a bit, though, is that HWinfo now displays silly voltage readings unless all cores are fully loaded, i.e. some cores report 0 V; others even 1.55 V. I am wondering if this is just buggy readings or something to worry about (1.55 V).
     
    Last edited: Oct 1, 2020
  9. Ristin

    Ristin New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    GeForce GTX 980Ti
    Hi folks,

    Here's my current setup:
    Ryzen 9 3900X
    Gigabyte X570 Aorus Elite w/ F30a BIOS
    CPU Vcore LLC set to: Turbo
    SOC LLC: Auto

    In both beta1 and beta2 I get a gold sample rating for my chip. It reports 1074mV and a power efficiency of 3.77. Standard cinebench R20 score of 3678.

    I run the tuning, I get around 7-10 steps in and then just hard crash and reboot. No logs produced. Each time I attempt to retry it starts from the beginning then hard crashes again. I am able to run the diagnostics with no issue, system is generally 100% stable and temps during the testing and tuning never peak above 65 degrees. I'm new to Zen2 so I'll hold my hand up and say I'm pretty green when it comes to AMD overclocking, am I doing something wrong or do I need to adjust something within my BIOS or hold out for another hotfix which may help me out ?
     
  10. Garwinski

    Garwinski Member Guru

    Messages:
    185
    Likes Received:
    4
    GPU:
    XFX Fury X
    I remember there is something specific in the guide when you the Core tags are nog defined correctly. So in this case, if you still have this problem, check the guide out from start to end again (like the error message said), somewhere in there this problem is mentioned.
     

  11. NewUserAskingQs

    NewUserAskingQs New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    GTX 1660 Ti
    Hi everyone. I have a small question: Once configured, does CTR need to run in the background or open on startup for the tuned profile to be applied every time? Thanks in advance for answering!
     
  12. daghtus

    daghtus Member

    Messages:
    25
    Likes Received:
    6
    GPU:
    RTX 2080S, 8 GB
    As long as "Apply profile with OS" is enabled, it should be started automatically but in Beta 1, it wasn't always the case.
     
  13. Swordfish

    Swordfish New Member

    Messages:
    1
    Likes Received:
    0
    GPU:
    RX 6800 XT Nitro+
    HWINFO shows my average CPU core voltage at 1.427v. I stopped using the app because I think that's too much.
     

    Attached Files:

  14. NewUserAskingQs

    NewUserAskingQs New Member

    Messages:
    2
    Likes Received:
    0
    GPU:
    GTX 1660 Ti
    So, do you mean to say that the program should be started automatically, or the profile is applied without the program running in the background automatically? And thank you.
     
  15. max1486

    max1486 New Member

    Messages:
    1
    Likes Received:
    0
    GPU:
    1080ti
    Does anyone know why my numbers are solid sticking on 100? I have checked every setting, it should work fine. I have a friend with a 3900X and a MSI GAMING EDGE WIFI as well, and he has same problem.

    [​IMG]
     

  16. daghtus

    daghtus Member

    Messages:
    25
    Likes Received:
    6
    GPU:
    RTX 2080S, 8 GB
    In my case, I see the app starting with the OS.
     
  17. pegasus1

    pegasus1 Maha Guru

    Messages:
    1,403
    Likes Received:
    349
    GPU:
    ROG 6900XT@2.3Ghz
    On my 3800x i looked at both the performance and power saving recommendations and the difference in voltage is significant. i went with the power saving which runs the CPU at 4200mhz but drops temps in many (CPU demanding) progs by 10C (on custom water) but i saw only a 1fps drop when i benched FC5 at 4k and max settings.
     
    Evildead666 likes this.
  18. Mufflore

    Mufflore Ancient Guru

    Messages:
    13,520
    Likes Received:
    1,819
    GPU:
    Aorus 3090 Xtreme
    I suggest keeping a drive with an OS backup on it for testing.

    ie backup your OS, restore to another drive, test what happens on that drive.
     
  19. Middle

    Middle New Member

    Messages:
    3
    Likes Received:
    0
    GPU:
    RX570
    1.JPG 2.JPG 3.JPG 4.JPG

    I still unable to open the software.
    I find some error in the Windows EVENT LOG
    I am now using Windows 10 2004 PRO
    Already try beta2 but no luck

    INFO#
    Here is my information under ctr_log

    ***ClockTuner for Ryzen 1.0s by 1usmus***
    AMD Ryzen 5 3500X 6-Core Processor (870F10)
    ASRock AB350 Pro4
    BIOS ver. P6.30 SMU ver. 46.54.00
    DRAM speed 3734 MHz
    10/01/2020 18:01:39


    I would appreciate if someone can provide any advice
     
  20. fry178

    fry178 Ancient Guru

    Messages:
    1,814
    Likes Received:
    291
    GPU:
    Aorus 2080S WB
    THIS WILL NOT HELP with gaming/normal use.
    since this is a "fixed" oc, running PBO (enabled, not just auto) will be better (especially for non MT clocks),
    and my CB20 result was actually tick higher (bit more power use tho).

    about cpu quali:
    i forgot that pbo was running, so switching pbo off, my 3700 went from platinum to bronze,
    so its not that reliable (for now at least).

    LLC setting:
    start with recommended setting, switch one down/up if needed.
    i got "lower LLC" warning on the beta v2, and switching from turbo to high (Aorus x570 Ultra)
    fixed it, and i didn't have more than 1% drop, nor did it affect my boost clocks.


    anyone having problems with the prog:
    -make sure you run the latest (non beta/stable) bios for your board/cpu (with needed settings)
    -make sure your ram is stable (3rd pass on memtest (v8.4) showed it wasn't anymore, i needed +0.01v more after update)
    -make sure net 4.6 is installed
    -make sure your running the latest chipset driver
    -make sure that you still have the zipped CTR folder (dl again if needed)
    -uninstall ryzen master, delete existing CTR folder, delete windows logs and registry (use ccleaner if you don't know how)
    -SHUTDOWN pc
    after boot:
    (use the amd balanced plan if possible)
    -install ryzen master, start it once and shut it down again
    -unzip CTR folder, copy CB files and run it once to accept conditions
    -start CTR and do "diagnostics", after its finished, do "start"..
     

Share This Page