AMD Catalyst 12.7 (8.981.2.0 June 26) AMD Official BETA

SSAA aint work in BF3/DX11.

 

Odd, RGSS seems to be working for me when I select MSAA in game and force Super Sampling via CCC. It looks a lot better than on my Nvidia rig that way.

 

Woot? can you please explain me how do you do that? i tried but nothing helps! even i already have BF3 looking amazing, in using SMAA injector (ultra settings) + high quality filtering in drivers and 4XMSAA, still would be great to see how does RGSS? looks i dont even know what that means, that is some kind of SSAA, right?

 

It does on AMD drivers....I can't say for Nvidia..

All I have to do is enable supersampling from CCC...that simple.

IQ goes through the roof adds negative LOD quality also. It's part of the drivers now.

 

When i flash with hd 7970 bios ghz edition than i install drivers and then tell me no drivers are in the pc for the card....

can someone post the right hd 7970 ghz bios ?

I have hd 7970 shapphire oc dual-x

 

http://forums.guru3d.com/showthread.php?t=365632

 

Getting the old corrupted mouse pointer issue with these.

 

Don't use atiflash/atiwinflash to flash the ghz bios on the card. You have to use the AMD unofficial crossflasher. Most likely, there is a CRC/hardware check, similar to when you tried using radeon Bios editor to change the CCC limits on the 6900 cards, then the drivers couldn't detect the card anymore. It's probably the EXACT Same thing going on, which is why you can't use atiflash to do this.

Reflash the backed up Bios (if you didn't back it up, switch to Bios #2, dump it with gpu-z 0.6.3, then with the power on, switch to Bios #1 then run the command line (or atiwinflash) flasher (it's best to boot to MSDOS/boot disk and flash with atiflash) to restore the original Bios. Then run the crossflasher that Rich Guy linked above for you.

 

Yep I used the official flasher, took 10 seconds. It flashed both my cards at the same time right in windows. No need for safemode and the like. It just worked, and great.

12.7 beta's came to life afterwards.

 

rich_guy you think i can take 60 min fps with a gtx 670 with this setting on bf3?

ultra
high
high
medium
ultra
ultra

2x msaa

HBAO

1920x1080

 

Ghost are you watercooling your 3770k for 4,6 Ghz?

 

Little feedback : these drivers crash Kane's Wrath (old game) with a big freeze. Must reboot by hand windows. Rollback to 12.6 and seems to work good :/

 

I don't play it, but i can't see why not, if the 7970 can handle it fine as said above

 

No, running a CoolerMaster V6 GT air cooler. I go back and forth between 4.6 to bench and 4.4 for gaming.

I don't bench too often though.

 

So I have a problem with the new model of CCC greater than 12.4. I am running a 6870 and an integrated 3300 (on a 790GX board, using it to drive my second monitor) and when I upgraded from 12.4 to this driver (and I tried 12.6) it could not find a driver for the 3300. I see that they switched to a legacy driver model for anything lower than the HD 5XXX. When I tried to load the driver from 12.4 for the 3300 it switched both cards to the 12.4 driver. I can't use different drivers for some reason. Am I able to run both cards (well one is an integrated motherboard chip) or am I stuck to using 12.4?

 

GhostXL where can i find the offical flasher? And do you have voltage control with that bios?

 

thanks a million. The problem though is now Catalyst Control Center is saying that 12.6 is newer than my 12.7 betas... and it wanted me to update... lol

I rarely use windows 7 so i almost forgot that i had the betas....

 

I'd like to mention about the grey/grey with vertical stripes etc 'screen of death' -I keep getting it while I'm on browser with HWA on, but only when I forget to reset the clocks after I finished playing...

In short, I got it 6-7 times only when I had applied manual overclocking... Do you get it anytime, even on fully stock clocks?

 

nope i've never , at stock clocks or extremely overclocked :banana:

 

Yes you have voltage control still and the flahser can be found in this thread.

http://forums.guru3d.com/showthread.php?t=365632