Radeon-ID Community Driver: Hybrid - Release Nebula 23.11.1 WHQL

++ I don’t feel the growth itself. I have a ryzen 5 5600x b550 chipset and some people allegedly have 60% on the ryzen 3000 series and the chips there like 450 and on sam they set such restrictions, I think we need to at least correspond to something so that at least somehow it works and not like that percent ancient mother identity videocard similarly.
System Requirements For AMD SAM

Hardware

• AMD 500 Series Motherboards
• Select AMD Ryzen™ 3000 Series Processors8
• AMD Ryzen™ 5000 Series Processors
• AMD Radeon™ RX 6000 Series Graphics

Software

• AMD Radeon Software Driver 20.11.2 or newer
• Latest Motherboard BIOS (based on AMD AGESA 1.1.0.0 or newer)

 

SAM doesn't seem to be enabled. Only 256MB of device-local, host-visible VRAM. Should be 4GB in your case.

 

Curiously, I only managed to enable SAM by installing 21.12.1 first and then upgrading to 22.1.2. Doing a clean installation of 22.1.2 did not enable SAM. Don't know if it was mere coincidence, It's possible that I did something wrong but you seem to be affected by the same problem too.

 

but this driver most likely fixes low fps in halo infinite since it was a sore for all vidyuhs until they released a fix pack

 

May B worked for me without ASIC mod and I didn’t even understand how I achieved this, I just played with firewood and somehow it happened later when I decided to demolish and try another, I couldn’t return to those settings, but I didn’t change the increase in games I found not in one of the options, but with the ASIC mod, terrible lags and the Radeon client always crashes

 

You can find out from you, even with SAM turned on, there was at least some tangible increase, I don’t know how anyone checks, I just start the game and look statically, let’s say at some wall and fix the fps difference of 1 fps, I think it’s an error you can go in 1 time will be 39 fps re-enter and see 40

 

DDU on Safe Mode worked for me, thank you very much. I had tried the other options first so as not to lose the configuration profiles.

 

by the way which gcn are you using and which version

 

The official requirements made by AMD are simply BS. I did some tests and made huge gains on my RIG. https://www.reddit.com/r/Amd/commen...izebar_be_supported_on_zen/he7a017/?context=3

 

According to the link with the SAM test, there is just the officially supported 5500XT card.

 

According to the requirements made by AMD, RX 5500 XT and R5 2600X are not supported ¯\_/(ツ)\_/¯ I don't know why but it just works on unspported configuration.

 

I did a bit testing with Nimez latest 22.1.2 driver with my R9 Fury and seems like that overall results are a bit worst then some previous drivers not by a lot but still....also I notice some strange stuttering and fps dips in War Thunder so I will probably install back 22.1.1........

 

I'm sure this caused by latest kernel provided.
I observe some kernel which i set default for:

• GCN 1.0 - 27.20.15030.3002
• GCN 2.0 - 27.20.15030.5001
• GCN 3.0 - 27.20.21034.37

Have you tried the GCN 1.0 kernel?

 

Yeah...probably...I tried just to install GCN 1.0 kernel over this and seems like stuttering in War Thunder stopped...'tho still didn't tried to do benchmarking and compare results

 

thank you so much for these drivers, i only created this acc to thank and to ask some qs ;p
I have a r9 380x i installed the ( 22.1.2 V4 ) Adrenalin GCN DCH (Mantle API, Store Apps Support) with the Adrenalin V4.0 > for Insight 21.12.1 - 22.1.2 Kernel V21 (GCN 3) ui dependencies
The only issue i have is that there is no UI but the drivers work fine as hell!
I made a mistake?(ofc ddu uninstall previous drivers on safe m properly etc)

 

Try to install Adrenalin Ver.3.5 in dependencies and do it after driver installation....that's how it worked for me....

 

As of final test in GCN 1, 2, and 3. We are alleged to use 27.20.15030.3002 as main kernel driver. Performance scaling across all games are bit better with 27.20.15030.3002.

 

Yep seems like that is the case....so did you FIX that also in latest driver installation?

 

W najnowszej wersji sterownika nie mogę aktywować karty graficznej SAM (V4-UWP-PolarisVegaNavi-WHQL-Insight-NimeZSlim-Adrenalin-22.1.2-Rev2.0-DCH)GPU Rx 580. SAM aktywny w kontrolerze 21.12 Jakaś pomoc?

 

Kernel all-in-one Revision will on next release 22.1.3 or 22.2.1, and this release will introduced gui simple setup.

Activate SAM with Legacy ASIC mode in NimeZ CLI setup