AMD Radeon Adrenalin Edition 20.2.2 driver download & Discussion

7z it first, kernel dumps compress well.

 

relive still randomly stops recording. I think it may be related to antilag, I use it often in hunt showdown as it makes game less sluggish. I think every time relive stopped by itself I was using antilag. Hard to confirm because it happens pretty rarely

 

This drivers no good too much for me. 800 Mhz idle core ¿bug? (2D). Also, temps when gaming go up to 4-5 cº, before 77-78 Cº, now go up to 82-83 cº (Junction up to 105º :S):



Reference 5700 XT underclock (1096 mV to 2056 Mhz). Memory bug in 2D with 144hz monitor still present too

 

your side of the world is heating up right now for one, and 2, better to have some more degree's and a stable gpu than chasing frozen unicorns.

thats not a bug.

 

With my previous reference VEGA 64, this problem was not present. So is a 5700 XT BUG (from begin, Im bought this card in July 2019)

 

its not a bug, and your comparison to a HBM vega is irrelevant.

Please understand the differences in bandwidth between a HBM interface at low clocks vs GDDR6.

5700XT on GDDR6 at 200MHz is 51GB/s

where as

Vega 64 on HBM2 2048bit @ 334mhz (167*2) is 86GB/s

 

I'm not entirely sure if it's the driver, but i have lower FPS in iRacing compared to the 20.1.4 driver.

 

.....

 

Go to "My Documents", then the iRacing folder and look for the file called "renderer.ini".

Right click and "open with" notepad. Once you have the file open you'll see this at the top

[AutoCfg]
AutoCfgCompleted=1

Change the 1 to a 0 and then save the file. Then restart iRacing and it will go through the auto config for graphic again.

 

I know i know, not my first time playing iRacing. Deleting the renderdx11 file is quicker anyway, though that does not solve my problem.

 

Oooooh sweetness, just tested for 6 hours (Fallout 76, Elite Dangerous and neverwinter) NO Blackscreen or crashes and i have Coretemp, MSIA/RTSS + rainmeter running again, i even dared tab out of game a few times

One thing though, for some reason i cannot get my fanspeed below 33% now in my fan curve, very minor issue as i usually set my idle fan to 25%'ish... just weird i cannot go lower than 33% is all (zero fan are gone as said earlier in thread and with the 33% fanspeed it is ~3-4 degrees hotter than previous at 25%, 34-35 degrees vs. 30-32 before at same room temp).
I guess i'll do a reset tomorrow and get it setup properly...

Happy camper here (for now, the Jinx is real)

 

has never happened to me

 

144Hz monitor here. 400MHz VRAM in GPU-Z - 200MHz in Wattman.

Your card doesn't look to be idle - 36W is far too much for that.

Did you need to raise power limit by 30?

 

Wattman setting reset after a reboot.
Performance Overlay still closes during play.

Maybe next driver...

 

Since that admin is on a power trip, defending a psycho, looks like this will be my last post.

https://forums.guru3d.com/threads/amd-radeon-adrenalin-edition-20-2-2-driver-download.430955/

Cheers)

 

No offense, but getting all miffed up on a forum is silly. HH always makes a download thread because it's attached to a news article he's posted. The "Official" thread is made by locals. Technically, HH would prefer we use his thread, so it gets tied to the article. But we don't, because, :shrug: prolly due to wanting it in the Radeon Driver forum instead where people will find it.

Anyhoo, just chillax, and don't take forums personal. Anonymity brings out the worst in people due to utter lack of responsibility of their words. (Doesn't apply to all, some respect themselves and others.)

 

Its a bug , if you can report to amd report site as well, not only here, i have the same problem. So of someone says otherwise dosent know what is he talking.

 

Does the same thing on default settings so thats not the problem.

 

All I did was make a suggestion.

He made it seem like I told him and others what to do.

Huge difference.

Other thread also HH's...

Whatever...

 

Hope AMD gets the rest now, soon. Cheers)