-=The Guru of 3D rig gallery rev.2 Part 8=-

wow.. thats wunderbar... I dont have wires to make most of my wires long enough... but u have made so ****ing great....

 

Hehe - I plan to clean this clutter even more - just waiting till my card gets from RMA to measure everything. I've also used 24pin and 8pin EPS12v extensions - already sleeved, made by NZXT. Also 2x6pin PCI-E power connectors are extended. My fan controller has 9 fans connected to its 6 channels at the moment, so even more cables and splitters.

But the inside looks not too bad (on this pic with old GFX card):


Whole gallery here:
http://corey.wmc24.pl/gallery/cm690_ii_advanced/index.html

 

New Case and New Card

 

I know you guys said i could of did better with the wiring so i did here is a update. Give me any suggestions please thanks

Before Cable Management





After Cable Fixing

 

@Victor Morales - Much better You have managed to put all the extra cables behind motherboard after all Looks much cleaner now - good job.

 

So thats how my FT-02 will look like once I fit it with a GTX 480 lol I wish

 

You need to be creative. Try to run cables so that they don’t pass directly under the management holes. Find the shortest route from the management hole to the component and only have the cables needed for those components visible through those holes. Try to bend and route those sata cables so that they look orderly and are all going in the same direction (this will take a lot of work and creativity. Be patient). Use up all the slack you can in your power cables by running them in folds behind your motherboard. Straight out of the PSU bundle all of your power cables together after untangling them so that they are all going the same direction. Hide all fan cables, if you cant hide them run them either vertically or horizontally along the edges of the case, only use 90 degree turns.

Correct cable management takes A LOT of time, creativity and patients. If you don’t want to put in the time I would advice just leaving it be. If you want to make it look perfect you will need to start over completely. Go to a hardware store and pick up zip ties and ziptie anchors. Cable management is all about hiding what you can and making what you cant hide look good.

 

A couple more.. Notice the back plate on the 480.






During normal gaming it averages at 75c and never passes 80c.

 

Up to date pictures. Cooling updated mostly.

 

Nice and clean man:thumbup: but I think you'r one 5870 short. A CrossfireX setup would fill your empty space below:banana:.

 

yeepppppp totally agree with the above post eeee

 

I have had HD 5870 CF already twice, too much problems.

I am better off with one card.

 

heres some snaps of my machine as it currently is.

*note, i plan on getting an Antec 1200 very soon and tidying the cables properly. The Antec 300 is a tad cramped, even though there isnt a single component in it that goes above 60C (gfx cards)

Let me know what u think!

Cheers

 

PLEASE dust the front of that case off

 

Holy crap man your case is growing fur! Please pull the front off take it outside and dust it off!

 

Yo! Hello guys!

Update>>

 

Dryroon: Isn't your CPU HSF sucking warm air off the back of your GPU and firing it through your PSU! How's your temps?

 

green enough?

 

ye here in brazil is very warm, but with this cooler + AS5 i havent problens! look:


i have a 120mm fan in my case backs to help! the psu fan is there for that, put out the warm air of the cpu and psu itself!

my temps is pretty good i think, with intelburntest my q9550 takes 62°C in a 29°C ambient temperature

in games it never pass than 52~55°C

i wont overclock more because the mobo, not the temps kk!

thank you!

no mann!!

i hope my razer lycosa will be green one day!! haha!

thank you!

 

@ Dryroon >>>>> nice setup their m8t..keep it up