Guru3D.com Forums

Go Back   Guru3D.com Forums > Videocards > 3D Stereo Gaming Section
3D Stereo Gaming Section In this stereo gaming section you can discuss everything 3D Goggles, monitors their drivers and graphics cards related.


Reply
 
Thread Tools Display Modes
Bad ghosting when I increase 3d depth
Old
  (#1)
MarcusarilliuS_
Newbie
 
MarcusarilliuS_'s Avatar
 
Videocard: 2 x Gigabyte GTX 670's
Processor: i7-2700k @ 4.8ghz
Mainboard: Asus P8Z68 Deluxe gen3
Memory: 16GB Dominator 1600mhz
Soundcard: x-fi titanium champion
PSU: Corsair HX850W
Default Bad ghosting when I increase 3d depth - 11-11-2012, 04:43 | posts: 18 | Location: Ireland

Whenever I increase the 3d depth by any amount I get bad separation.

I mess with the convergence but it's a trade off of either having near objects not separating or far objects.
Can't find a sweet spot.

On default it is fine but I'd like to play at higher depths without getting this.

I'm using a panasonic L55ET5B passive 3DTV with the Zalman edid override, so it's detected as 3dvision display and outputting in interleaved mode.
Running 1920x1080@60fps.

Any solution?

Thanks,

Mark.
   
Reply With Quote
 
Old
  (#2)
Fox2232
Maha Guru
 
Videocard: Accelero7970 1125/1500MHz
Processor: i5-2500k@4.5GHz NH-D14
Mainboard: MSI Z68A-GD80[g3]
Memory: 4x4GB 1600MHz 9,9,9,24
Soundcard: Essence ST / AKG K-701
PSU: FSP Gold series 750W
Default 12-28-2012, 10:22 | posts: 1,498 | Location: EU, CZ, Brno

I would create image 1920x1080 with horizontal red and blue lines so one eye should see only red and another only blue screen. If you see anything else or it appears as color gradient then you have incorrect image scaling set in TV or nV CP.

You should not use any image processing on TV level while you use it as PC monitor. And overriding EDID may have it's own disadvantages like incorrect color profile, timing.

If you have weird stuff on screen in above Red/Blue test pattern then make another one:
image 1920x1080, left side Blue, right side red. Set TV into manual 3D mode "Side by Side" Incorrect scaling should not matter in this mode. If you still see color gradient/shift then problem is in your viewing angle or distance.

Yes, you can sit anywhere on left/right from TV, no problem, but if you are too much above/below horizon then FPR intersects light from wrong pixels for you. Same goes for cases when you are too close.

As far as I know those panels were supplied by LG and do not suffer from ghosting. On LG TVs there was firmware bug causing minor ghosting on red/green. Panasonic should not suffer from this since they use their own electronics.
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Forum Jump



Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Skin developed by: vBStyles.com
Copyright (c) 1995-2014, All Rights Reserved. The Guru of 3D, the Hardware Guru, and 3D Guru are trademarks owned by Hilbert Hagedoorn.