Guru3D.com Forums

Go Back   Guru3D.com Forums > General Chat > The HTPC, HDTV & Ultra High Definition section
The HTPC, HDTV & Ultra High Definition section Home Theater PC Enthusiasts or want to talk in High-Definition ? This is Guru3Ds Premier Community of HD and HTPC.



Reply
 
Thread Tools Display Modes
Mounting question for new 4k TV
Old
  (#1)
Brogan
Maha Guru
 
Brogan's Avatar
 
Videocard: 980 G1
Processor: i7 6700
Mainboard: GA-170X-UD3
Memory: 16GB 3200MHz
Soundcard: X-Fi
PSU: G2 SuperNOVA 750
Default Mounting question for new 4k TV - 11-29-2016, 06:05 | posts: 1,009 | Location: east coast

Hey all. Just recently purchased a new Samsung 4k TV. And I have an older TV stand with a rear swivel mount that uses this type of adapter:
)

In looking at the TV's installation pdf, it provides two (2) threaded wall mount adapters (spacers) ONLY for the upper 2 mounting locations on the back of the TV (standard Vesa 400x400 setup). Link here.

I have no worries about the stand holding the TV, as it's currently holding a 90 lb plasma without issue (the ks8000 is half that). What I'm curious about is what kinds of issues I may run into when attaching the vertical monitor brackets to the TV using the (nearly) 2 inch long spacers just on the top mounts of a TV this narrow:


I know I have some extra long screws that came with the swivel mount (and if I don't, I can easily purchase some). I just wonder if once I attach the brackets, will the screws extend far enough into the upper mounting holes to be safe (no, I don't yet have the spacers to measure), or will the TV then be tilted overly forward with these huge adapters for a barely noticeable curve of the back of the set?

If anybody has any experience with mounting this kind of set to a wall mount or stand with this type of bracket and could give me some advice, I'd appreciate it.
   
Reply With Quote
 
Old
  (#2)
Netherwind
Ancient Guru
 
Netherwind's Avatar
 
Videocard: MSI 1080Ti 2038/12006MHz
Processor: Intel i7 6700K 4500MHz
Mainboard: MSI Z170 M5
Memory: Corsair 16GB Ven. 2666MHz
Soundcard: ALC1150 & Creative T20
PSU: EVGA Supernova G2 850W
Default 11-29-2016, 14:52 | posts: 4,808 | Location: Sweden

I have the same as you only it's the 7 series. From what I've read the back panel has a tendency to start to loosen up after a while. Not sure if this applies to the 8 and 9 series too but I'd make sure I know what I'm doing before mounting anything. For me it's natural that you attach the TV to four connectors on the back and not just two.

For the record mine is on a bench and not mounted.
   
Reply With Quote
Old
  (#3)
Brogan
Maha Guru
 
Brogan's Avatar
 
Videocard: 980 G1
Processor: i7 6700
Mainboard: GA-170X-UD3
Memory: 16GB 3200MHz
Soundcard: X-Fi
PSU: G2 SuperNOVA 750
Default 11-29-2016, 22:24 | posts: 1,009 | Location: east coast

Hmm.... after looking at that pdf, it seems I was mistaken about only using 2 spacers. It looks like you do indeed have to use 4.

Either way, I guess I'll wait and see when it arrives. I'm not too worried about it.
   
Reply With Quote
Old
  (#4)
Steppzor
Master Guru
 
Steppzor's Avatar
 
Videocard: Gigabyte 980 TI G1
Processor: Intel i7-4770K @ Stock
Mainboard: Gigabyte GA-Z87X-UD3H
Memory: Corsair Vengeance 16GB
Soundcard: Kingston HyperX Cloud II
PSU: XFX ProSeries BE 1050W
Default 01-02-2017, 08:40 | posts: 682 | Location: Norway

Hi OP, how do you like the TV? I just ordered the same model myself and waiting for it to be delivered.
   
Reply With Quote
 
Old
  (#5)
Pyr0
Master Guru
 
Pyr0's Avatar
 
Videocard: EVGA GTX 980 SC ACX 2.0
Processor: Intel 6700K
Mainboard: Asus Z170 Deluxe
Memory: 16GB 3200C14 G.Skill TZ
Soundcard: Asus Xonar DX/Logi Z-5400
PSU: Corsair HX850
Default 01-02-2017, 11:22 | posts: 587 | Location: UK

You should have 4 plastic spacers that come with the tv.
With those I used 4x 45mm m8 button heads to fasten the vesa mount.
   
Reply With Quote
Old
  (#6)
Hammie
Master Guru
 
Hammie's Avatar
 
Videocard: 760 SMG 28" 1ms 3840x2160
Processor: 4930k Ivy-E 4.5Ghz 12HT
Mainboard: ASUS Sabertooth X79 64GB
Memory: Corsair Veng. 1890 @ 9CL
Soundcard: Xonar D2 & KRK Rokit 10-3
PSU: Corsair AX860
Default 02-09-2017, 20:16 | posts: 551 | Location: Glendale, CA

Congrats, Nice TV. Glad you didn't get curved. Curved cant be put on a wall,

And probably wont fit in the wall unit you bought. gl
   
Reply With Quote
Old
  (#7)
kynek
Newbie
 
Videocard: gt 540m/2gb
Processor: Intel core i5
Mainboard:
Memory:
Soundcard:
PSU: SeaSonic SS-400ET 80+ 400
Default 05-22-2017, 14:46 | posts: 5

Hmmm
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Powered by vBulletin®
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
vBulletin Skin developed by: vBStyles.com
Copyright (c) 1995-2014, All Rights Reserved. The Guru of 3D, the Hardware Guru, and 3D Guru are trademarks owned by Hilbert Hagedoorn.