Guru3D.com Forums

Go Back   Guru3D.com Forums > Affiliates > Rivatuner Generic Discussion forum > RivaTuner Advanced Discussion forum
RivaTuner Advanced Discussion forum This forum is intended for advanced comments, ideas and general discussion of the RivaTuner Utility which is hosted here at the Guru of 3D. This forum is visited by programmer himself - you can only post in this area with a minimum of 10 posts and 7 days forum membership.


Reply
 
Thread Tools Display Modes
who helps me to understand rivatuner
Old
  (#1)
alco
Maha Guru
 
alco's Avatar
 
Videocard: Asus gtx780 DirectcuII OC
Processor: 4770K @ water
Mainboard: Gigabyte Z87 OC-Force
Memory: 16 Gig Ripjaws
Soundcard: Soundblaster ZXR
PSU: C.master silent pro 1000W
Default who helps me to understand rivatuner - 11-20-2005, 18:40 | posts: 935 | Location: Netherlands

1st of all thx for this wonderfull program unwinder
i am shure you made the world a better place for some of us


now there is something i want to now about my card
here is some info from rt.

$ffffffffff NVIDIA VGA BIOS information
$ffffffffff ---------------------------------------------------
$1100000000 Title : NVIDIA GeForce 6800 GT VGA BIOS
$1100000002 Version : 5.40.02.38
$1100000100 BIT version : 1.00
$1100000200 Core clock : 200MHz
$1100000201 Memory clock : 600MHz
$1100010000 Perf. level 0 : 350MHz/500MHz/1.30V/100%
$1100010001 Perf. level 1 : 350MHz/500MHz/1.40V/100%
$1100020000 VID bitmask : 00000011b
$1100020100 Voltage level 0 : 1.10V, VID 00000000b
$1100020101 Voltage level 1 : 1.30V, VID 00000010b
$1100020102 Voltage level 2 : 1.40V, VID 00000001b
$1100000003 SW masked units : none

can i make up from this that my card should do 400 core and 1200 memory ?
i can make the core to 400 with no problems but the memory is holding me back
got the card wc so temps on the core r no problems

what i wanna know is how can i (if it isn't already) see or make my card run @ 1.4 volt
to c if it helps the overclocking
i have read alot of treaths about riva tuner
but i think my english isn't good enough to fully understand all the subjects being discussed about it

so my 2 questions r
1- how to change the voltage (if needed) i think i do
2- can i c at what voltage my card is running in 3d mode
hope you guys/girls can help me out

tia DSP
   
Reply With Quote
 
Old
  (#2)
alco
Maha Guru
 
alco's Avatar
 
Videocard: Asus gtx780 DirectcuII OC
Processor: 4770K @ water
Mainboard: Gigabyte Z87 OC-Force
Memory: 16 Gig Ripjaws
Soundcard: Soundblaster ZXR
PSU: C.master silent pro 1000W
Default 11-20-2005, 19:46 | posts: 935 | Location: Netherlands

i just played a little with nibitor
i think my gpu run at 1.4v in 3d
but i can change the voltage acording to the voltage table
to 1.6v
is 1.6 still a safe voltage or wil it fry the card

let me know
thx
   
Reply With Quote
Old
  (#3)
IbSta
Newbie
 
Videocard: ASUS N6200 256 DDR OC!
Processor: Pentium 4E HT / 3.2 Ghz
Mainboard: ASUS P4P800-SE 1010.001 BETA 1
Memory: 2 Gigs Kingston PC3200 DDR-2 500 Mh
Soundcard: Audigy Platinum 7.1
PSU: 550 Watts
Default 11-21-2005, 06:17 | posts: 5 | Location: Canada

1.6 is pretty damn dangerous basically your risking your card at that point
   
Reply With Quote
Old
  (#4)
alco
Maha Guru
 
alco's Avatar
 
Videocard: Asus gtx780 DirectcuII OC
Processor: 4770K @ water
Mainboard: Gigabyte Z87 OC-Force
Memory: 16 Gig Ripjaws
Soundcard: Soundblaster ZXR
PSU: C.master silent pro 1000W
Default 11-21-2005, 17:55 | posts: 935 | Location: Netherlands

*bump*

can someone take a look at the dump of my bios like above
and give me some details



@IbSta so you think i shouldn't try 1.6 volts
there was also 1 more choice but that looked something like ?.?
   
Reply With Quote
 
Old
  (#5)
DrSiN
Ancient Guru
 
Videocard: GeForce GTX 560 Ti OC 1G
Processor: Core i5 2500K @ 4.9GHZ
Mainboard: MSI P67 GD53
Memory: 8GB Corsair 1600 CAS 7
Soundcard: Creative SB X-Fi Xtreme M
PSU: Corsair 800W
Default 11-21-2005, 18:08 | posts: 3,176 | Location: UK / Derbyshire

it should be 1.5
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vBulletin Skin developed by: vBStyles.com
Copyright (c) 1995-2014, All Rights Reserved. The Guru of 3D, the Hardware Guru, and 3D Guru are trademarks owned by Hilbert Hagedoorn.